|
Sensing mode
|
Through-beam
|
Retroreflective (M.S.R.)
|
Diffuse-reflective
|
|
Cable type
|
NPN
|
PQ-T30N
|
PQ-M4N
|
PQ-R1N
|
|
PNP
|
PQ-T30P
|
PQ-M4P
|
PQ-R1P
|
|
Connector type
|
NPN
|
PQ-T30NC
|
PQ-M4NC
|
PQ-R1NC
|
|
PNP
|
PQ-T30PC
|
PQ-M4PC
|
PQ-R1PC
|
|
Sensing distance
|
30 m
|
0.1 ~ 4 m
|
1 m
|
|
Hysteresis distance
|
-
|
20 % or less of detection distance
|
|
Detecting object
|
Ø12 mm or more (Opaque)
|
Ø60 mm more (Opaque)
|
White paper (100 x 100 mm)
|
|
Light source (wavelength)
|
Infrared LED (855 nm)
|
Red LED (660 nm)
|
Infrared LED (855 nm)
|
|
Current consumption
|
Emitter : max. 15 mA,
Receiver : max. 20 mA
|
Max. 30 mA
|
|
Power voltage
|
12 - 24 V d.c. Class 2 ±10 % (Ripple max. 10 %)
|
|
Control output
|
▪NPN or PNP open collector output
|
|
▪Load current - max. 100 mA (26.4 V d.c. standard)
|
|
▪Residual voltage - NPN : max. 1.5 V, PNP : max. 1.5 V
|
|
Operation mode
|
Light ON / Dark ON button switch type
|
|
Indicator light
|
▪Control output indicator light : Red LED
▪Stability indicator light : Green LED
(However, the green LED of the through-type emitter is a power indicator)
|
|
Auto
teaching
|
Through-beam
|
If the B2 (_01.png) ) button is pressed for more than 3 seconds in the presence of a
detection object, the sensitivity is automatically set.
|
|
Retroreflective
(M.S.R.)
|
|
Diffuse
reflective
|
1) In the presence of a detection object (stable light incident)
2) Release the B2 () button after pressing it for more than 3 seconds.
3) Check the green + red LED cross blinking (try again if either side is not
blinking)
4) Press the B2 () button once after removing the detected object
(0.5 seconds)
|
|
AGC
|
When the unstable light enters for 20 sec or more in button locked state, automatically changes to the stable light state.
|
|
Sensitivity adjustment
|
B1 increases the sensitivity and B2 decreases the sensitivity
|
|
Protection
circuit
|
Common
|
Power reverse connection protection, Output short-circuit over-current protection,
Output reverse connection protection, Output short-circuit alarm
|
|
Individual
|
-
|
Mutual interference prevention function
|
|
Response time
|
Max. 1 ms
|
|
Insulation Resistance
|
More than 20 MΩ (500 V d.c. mega)
|
|
Noise immunity
|
Square wave noise by noise simulator (pulse width 1㎲) ±240 V
|
|
Dielectric strength
|
1,000 V a.c. (50/60 Hz for 1 minute)
|
|
Vibration resistance
|
10-55Hz, sweep : 1.5mm, X·Y·Z 2 in each direction for 2 hours
|
|
Shock resistance
|
500 m/s², X·Y·Z each direction 3 times
|
|
Ambient illumination
|
Sunlight : max. 11,000 lx / Incandescent : max 3,000 lx
|
|
Ambient
temperature range
|
operating temperature : -20 ~ +55 ℃
During storage : -40 ~ +70℃ (Without condensation or icing)
|
|
Ambient humidity
|
35 ~ 85 % RH (Without condensation or icing)
|
|
Pollution degree
|
3 rating
|
|
Protection
|
IP67 (IEC standard)
|
|
Certification
|
(The connector type is
currently undergoing CE and UL certification)
|
|
Weight
(Packing)
|
Cable type
|
100 g (160 g)
|
55 g (115 g)
|
55 g (100 g)
|
|
Connector
type
|
20 g (80 g)
|
10 g (70 g)
|
10 g (55 g)
|
|
Texture
|
Case
|
NYLON
|
|
Display
|
PC
|
|
Lens
|
PMMA
|
|
Accessory
|
Common
|
Instructions manual, bracket A, bolt (M3 X 12 mm)
|
|
Individual
|
-
|
Mirror (HY-M5)
|
-
|
|
Connection
method
|
Cable type
|
Number of wires - 3P, Outer diameter - 4Ø, Length - 2 m
(however, the emiiter of through-beam type has 2P)
|
|
Connector
type
|
M8 Connector Wiring (M8 relay cable sold separately)
|
